Hyundai Elantra Owners and Service Manuals

Hyundai Elantra: Steering System / Specifications

Specifications
Item
Specification
Type
Electric Power Steering System
Steering gear
Type
Rack & Pinion
Rack stroke
154 mm (6.0630 in.) ± 1 (0.3937 in)
Steering angle (Max.)
Inner
39.7° + 0.5 / -1.5
Outer
32.7°

Tightening Torques
Item
Tightening torque (kgf.m)
N.m
Kgf.m
lb-ft
Tire wheel hub nut
107.9 - 127.5
11.0 - 13.0
79.6 - 94.0
Universal joint to steering column assembly
49.0 - 58.8
5.0 - 6.0
36.2 - 43.4
Steering column mounting nuts
25.0 - 29.4
2.5 - 3.0
14.5 - 21.7
Steering column mounting bolt
53.9 - 58.8
5.5 - 6.0
39.8 - 43.4
Front axle to tie rod end
34.3 - 44.1
3.5 - 4.5
25.3 - 32.5
Tie rod end mounting nut
49.0 - 53.9
5.0 - 5.5
36.2 - 39.8
Front axle to lower arm
68.6 - 80.4
7.0 - 8.2
50.6 - 59.3
Sub flame to steering gear box
107.9 - 127.5
11.0 - 13.0
79.6 - 94.0
Universal joint to steering gear box
49.0 - 58.8
5.0 - 6.0
36.2 - 43.4
Steering wheel mounting bolt
44.1 - 53.9
4.5 - 5.5
32.5 - 39.8
MDPS motor mounting bolt
8.0 - 12.0
0.82 - 1.22
5.9 - 8.8
Heat protector mounting bolt
6.9 - 10.8
0.7 - 1.1
5.1 - 8.0

    Troubleshooting

    T..

    Special service tools

    Special Service Tools Tool (Number and Name) IIIustration Use 09568-1S100Ball joint removerSaperate the ball joint from the front alxe09563-IB000Small bearing removerRemove the small bearing09563-IB200Small bearing installerInstall the small bearing..

    Other information:

    Hyundai Elantra (CN7) 2021-2025 Service Manual: Repair procedures


    Removal [Front Seat Belt Pretensioner (BPT)]1.Disconnect the negative (-) battery terminal.2.Remove the door scuff trim.(Refer to Body (Interior and Exterior) - "Door Scuff Trim")3.Remove the center pillar lower trim.(Refer to Body (Interior and Exterior) - "Center Pillar Trim")4.Remove the center pillar upper trim.(Refer to Body (Interior and Exterior) - "Center Pillar Trim")5.Remove the front se..

    Hyundai Elantra (CN7) 2021-2025 Service Manual: Knock Sensor (KS)


    Description and operation DescriptionKnocking is a phenomenon characterized by undesirable vibration and noise and can cause engine damage. Knock Sensor (KS) is installed on the cylinder block and senses engine knocking. When knocking occurs, the vibration from the cylinder block is applied as pressure to the piezoelectric element. At this time, this sensor transfers the voltage signal higher t..

    Categories

    Rear center seat belt

    When using the rear center seat belt, the buckle with the “CENTER” mark must be used.

    WARNING

    Make sure that the seatback is locked in place when using the rear center seat belt.

    If not, the seatback may move when there is a sudden stop or collision, which could result in serious injury.

    read more

    Copyright © 2025 www.helantra7.com